MOTF PREMIUM VISCOSE FORM FITTING SLEEVELESS TOP Shown 11 shells from the bottom and 5 shells from the inside edge/back seam. The belt placement can easily be adjusted for size. Count shells up from the bottom and across from the opening so that belt is positioned evenly. Tape the top of the feather to the template and trim the feather. Trim to make a feather shape or cut out a cardboard template. Watch the Video tutorial for a knotting demonstration. Fill in the 2.5″ gap, and cut more pieces if needed. Knot 2 pieces together, alternate knot direction. Cut 48 pieces of yarn 8″ in length per feather (96 total). Tail is used as the base for the feather. leave a starting and finishing tail of approx. Use all 3 strands with a 5.5mm hook and make a long chain. When seaming go through dc st, and ch-1 sp on each side.Ĭut 3 pieces of yarn 240 (240, 300, 360)” in length, making a belt approximately 50 (50, 60, 70)” long. Leave a 5 (6, 6, 6)” opening at the bottom of coverup, pm. Make sure all the shells and dc sts are perfectly lined up. RS facing fold coverup in half at shoulders. The last few stitches gradually lace so that it tightens, closing in the gap. Make sure that the yarn is pulled through evenly. Weave each end of the yarn with a yarn needle through marked sts. Double-check count for accuracy.Ĭut a piece of yarn 300″ in length. The back is seamed in shoe lace style leaving a. Place the final Row to the inside and Row 1 of each panel to the outside. Lay the rectangle panels side by side RS facing upwards. Dampen garment and pin piece to measurements. Row 30 (34, 38, 42): Rep Row 2, Fasten off and weave in ends. Row 5: Ch 4 (counts as dc, ch 1), work 1 dc in cluster, * ch 1, work 1 dc in next cluster rep from * across, turn-211 (223, 235, 235) sts. Row 4: Ch 3 (counts as first dc of cluster), (work 2 dc cluster, ch 1, work 3 dc cluster) in first ch-1 sp, ch 1, * work (3 dc cluster, ch 1, 3 dc cluster, ch 1, 3 dc cluster) in ch-2 sp, ch 1 rep from * across, end with, work (2 dc cluster, ch 1, 2 dc cluster) in last ch-1 sp, turn-36 (38, 40, 40) cluster shells. Row 3: Ch 4 (counts as 1 dc, ch 1), work 1 dc first st, *ch 2, sk 2 sts, work 1 sc in next st, ch 2, sk 2 sts, work V st (ch 2) next st rep from * across, ending with V st (ch 1), turn-36 (38, 40, 40) V sts. Row 2 (RS): Ch 1 (not included as a st here and throughout), work 1 sc in first dc, *work 1 sc in ch-1 sp, work 1 sc in dc rep from * across, ending with 2 sc in turning ch, turn-211 (223, 235, 235) sts. My photos are copyright protected and are not to be used to sell your items. I require a reference or link for my design. You are welcome to sell your finished items from this pattern. This pattern is copyright protected and cannot be copied or reproduced in any way. This pattern is the sole property of MJ’s Off the Hook Designs. V Stitch (ch 2) – In indicated stitch, work 1 dc, ch 2, 1 dc, all in the same st.Ģ Dc Cluster Stitch – Yo (yarn over), go through indicated stitch and pull up a loop, yo, pull through 2 loops, yo, going through the same st, pull up a loop, yo, pull through 2 loops, yo, pull through all 3 loops on the hook.ģ Dc Cluster Stitch – Yo (yarn over), go through indicated stitch and pull up a loop, yo, pull through 2 loops, *yo, going through the same st, pull up a loop, yo, pull through 2 loops rep from *, yo, pull through all 4 loops on the hook. Stitch (ch 1) – In indicated stitch, work 1 dc, ch 1, 1 dc, all in the same st. Choose size based on desired finished dimensions. Step by step video tutorial is provided on our YouTube channel for M-XL size. The pattern is written for the smallest size with larger sizes in parentheses ( ). Make 2 large rectangles and lace the back together. The Lacy Days Kimono is worked in 2 pieces from the side across. – Work step in brackets number of times indicated Construction ( ) – Work step in parentheses in indicated stitch
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |